Inhalt der "nvramUnique.txt"
# WD Navigator
# $Id: nvramUnique.txt 125 2005-05-10 08:29:05Z sun_r $
#
# 1.02 - Added nfs_secure settings
# - Set disk_health_query_ctrl=never
# 1.03 - Added critical_printer_pool_name=Main
###################
# CFE version
###################
wd_cfe_rev=1.03
###################
# Various board specific values
###################
boardtype=0x042f
boardnum=${serno}
boardrev=0x10
boardflags=0
#Needed for disk auto creation
broadnas_unique_id=40:10:18:00:00:00
# [ Hardware ]
###################
# Memory layout
###################
dl_ram_addr=a0001000
os_ram_addr=80001000
os_flash_addr=bfc40000
scratch=a0180000
###################
# CPU settings
###################
clkfreq=264
###################
# RAM settings
###################
# 64 MB DDR SDRAM (16 Meg x 16 x 2)
sdram_init=0x0549
sdram_config=0x8062
sdram_refresh=0x0000
sdram_ncdl=0
###################
# Ethernet settings
###################
et0macaddr=00:90:a9:01:${maclo}
et0phyaddr=0
et0mdcport=0
# MAC address of 40:... -> local address
# PHY address of 31 means no PHY
et1macaddr=40:10:18:00:00:00
et1phyaddr=31
et1mdcport=1
wlan_hardware_present=no
###################
# IDE settings
###################
force_ide_cable_select=on
initial_disk_spin_down_setting=180
disk_health_query_ctrl=never
###################
# Misc hardware settings
###################
watchdog=0
###################
# GPIO settings
###################
sda_gpio=2
scl_gpio=5
reset_gpio=7
# [ Software Stack ]
###################
# CFE behavior
###################
cfe_mfg_lan_proto=dhcp_client
critical_printer_pool_name=Main
###################
# GPIO setup
###################
gpio_0_name=soft_power_switch
gpio_1_name=system_ready_LED
cfe_gpio_early_init_out_1=0
cfe_gpio_early_init_out_4=0
cfe_gpio_init_out_3=0
cfe_gpio_init_out_6=0
cfe_gpio_init_out_4=0
kernel_gpio_early_init_out_1=0
kernel_gpio_early_init_out_4=0
kernel_gpio_init_out_4=1
kernel_gpio_init_out_3=1
kernel_gpio_init_out_6=1
###################
# Drivers to use
###################
rtc_device=st4181
misc_io_mode=bcmgpio
###################
# Fileystem
###################
default_cifs_master_enable=enabled
default_nfs_master_enable=enabled
default_nfs_write_enable=enabled
cifs_master_enable=enabled
nfs_master_enable=enabled
nfs_write_enable=enabled
default_nfs_secure=no
nfs_secure=no
###################
# Printer Spooling
###################
default_print_spool_auto_create=enabled
print_spool_auto_create=enabled
###################
# Networking
###################
lan_proto=dhcp_client
lan_ipaddr=192.168.1.5
lan_netmask=255.255.255.0
#wlan_ipaddr=192.168.21.1
#wlan_netmask=255.255.255.0
lan_ifnames=eth0 eth2
initial_disk_spin_down_setting=180
lan_ifname=eth0
#wlan_ifname=eth2
wan_ifname=eth1
###################
# Misc Behavior
###################
soft_power_down_immediate_reboot=enabled
#kernel_boot_wait_gpio=0
custom_shutdown_command=wdshutdown
startup_command=wdstartup
###################
# Broadcom Defaults
###################
default_physical_authentication_enable=disabled
default_http_username=
default_http_passwd=
default_workgroup=WORKGROUP
default_new_disk_action=one_jbod v
default_primary_pool_name=Main
default_primary_share_name=Shared Files
default_start_page=/setup/index.asp
default_machine_name=WD-NetCenter
physical_authentication_enable=disabled
http_username=
http_passwd=
workgroup=WORKGROUP
start_page=/setup/index.asp
new_disk_action=one_jbod
primary_pool_name=Main
primary_share_name=Shared Files v
machine_name=WD-NetCenter
###################
# QOS Settings
###################
qos_enable=no
qos_level1_common=
qos_level1_custom=
qos_level1_file_extensions=
qos_level2_common=
qos_level2_custom=
qos_level2_file_extensions=
qos_all_custom=
###################
# UPnP Settings
###################
wdupnp_media_path=/shares/Main/Shared Media
###################
# Misc Settings
###################
web_hook_libraries=corewebhooks netwebhooks diskwebhooks winnet printwebhooks wdhooks
wd_nvram_version=1
cfe_password_protect_tftp=enabled
cfe_configuration_state=initialized
goto_mfgstate_pattern=0
Inhalt der "Release_Notes_R1.0.0.0115.txt":
Build R.1.0.0.0115 6/09/05
- Updated full firmware version
- Removed ICS message in network page
- Replaced CFE with 1.2.1 RC1 version to fix long reset issue
- Fixed Responder that causes Mac EasyLink timeout when no shares are detected
Build R.1.0.0.0111 6/07/05
- Fixed set time issue v
- Fixed or Added more on-screnn help in create a new share, drive management and printer sharing page.
- Replaced CFE 1.3.4 to correct long reset problem
Build R.1.0.0.0110 6/02/05
- Removed mirror caution message in create a new volume page
Build R.1.0.0.0107 5/19/05
- Fixed ITR #7153
- Removed mirror setting
- Set default setting to manual mode for volume creation
- Mac 10.2 safari 1.0.3 Unclaim error issue
Build R.1.0.0.0106 5/18/05
- Added pcibios.c patch to fix USB reset issue
Build R.1.0.0.0105 5/17/05
- Fixed #ITR758 Incorrect USB unallocated space after being selected as a mirror volume
- Updated troubleshooting image files
Build R.1.0.0.0104 5/17/05
- Fixed #ITR7144 Internal drive health shows unknown for disk health
- Fixed #ITR7146 Mac OS 10.4 Safari Cannot change the security settings
- Fixed #ITR7152 Create volume on any OS and browsers gives Wrong message after completion
- Fixed #ITR7153 Mac OS 10.4 w/ Safari Create volume> available space proceeds with warning
- Fixed #ITR7154 Mac OS 10.3 and 10.4 with Safari Rename Drive gives error after completion.
- Fixed #ITR7155 Mac OS with Safari Safe Remove of USB Drives does not takes any action
- Fixed #ITR7156 Mac OS 10.3.9 with Firefox and Safari FW Upgrade Fails
- Changed startup script and moved volume and samba checks to the end of the script
- Changed version number format to 1.x.x.xxxx
Build 103 5/13/05
- Migrated to new build labels
Build R.0.9.2_130-101 5/13/05
- Fixed #ITR 7129 Mac OS 10.4 Firefox FW Upgrade does not work
- Fixed #ITR 7121 Mac OS 10.4 with Safari 2.0 failed for drive management and file sharing
- Fixed #ITR 7137 Change View Details to Unknown for USB drive on View Disk Health
- Fixed #ITR 7091 Mac OS 10.4 Safari Resize a volume, screen goes blank
- Fixed #ITR 7099 Full Erase time for 250GB drive estimated to be 362 hours. Broadcom issue
- Fixed #ITR 7123 IE Web page errors with critical error reported. (Win2K PRO)
- Many Fixes for Safari 2.0, 1.0.3…
Build R.0.9.2_124-100 5/9/05
-Fixed ITR: 7119 Disk Health is shown as unknown internal drive
-Updated SDK to 1.2 RC3
-Take out Unallocated column from "Broken Disk" under "Drive Management"
-Fixed UI problem for if there is no file sharing info under the "File Sharing"
-Add Foreign Share info into "System Summary"
-Fixed "Remove a Volume" doesn’t show error message problem.
-Disable submit button during firmware update
Build R.0.9.2_114-99 5/5/05
- Fixed ITR#7107 Add share shows pool in step 2
- Fixed ITR#7127 Add a share without volume name does not give error
- Fixed Several Safari/Firefox issues(create volume, mirror check box kills browser, slider bar… )
- Updated gpiosetup scripe and disk_health_query_ctrl=never
- Updated responder to support extended function reuired for Mac OS 10.1
Build R.0.9.2_104-98 5/4/05
- Fixed ITR#7120 SMART Data is Wrpped Around
- Fixed ITR#7114 Mac, General Setup, Device and Workgroup names wrap the closing parenthesis \
- Fixed ITR#7104 Incorrect drive status w/ a blank drive
- Fixed ITR#7107 Add share shows pool in step 2
- Updated banner graphics
Build R.0.9.2_102-97 5/2/05
- Fixed ITR#7079 Setting network address manually - What is Wins Server IP Address
- Fixed ITR#7089 Add "% Free" column to Drive Management Page
- Fixed ITR#7104 Incorrect drive status w/ a blank drive
- Fixed ITR#7106 Device Name with Space is rejected
- Fixed ITR#7107 Add share shows pool in step 2
- Fixed ITR#7110 Printerpool not assign with manufacturing reset
Build R.0.9.2_97-96 4/27/05
- Fixed ITR#7089 Add "% Free" column to Drive Management Page
- Fixed ITR#7087 Accepts the share name with special characters such as ;; "etc.
Firmware page loading problem fixed7093 Remove File-Level QoS
- Fixed ITR#7092 Drive Management Table -- Values not in proper columns
- Fixed ITR#7089 Add "% Free" column to Drive Management Page
- Fixed ITR#7087 Accepts the share name with special characters such as ;; "etc.
- Fixed ITR#7079 Setting network address manually - What is Wins Server IP Address
- Updated SDK to 1.2 RC1
Build R.0.9.1_91-95 4/22/05
- Fixed ITR#7049 No warning when attempting to remove a volume containing the printer pool
- Fixed ITR#7085 Show unallocated space in drive management
- Fixed ITR#6974 Resize volume - allows entry of size < used space on the volume
Build R.0.9.1_88-94 4/20/05
- Fixed ITR#7935 Obtain Network Address "Automatic" for DHCP gives Invalid LAN IP Address
- Fixed ITR#7042 Web-UI Getting New IP address show error data on page, though completed OK.
- Fixed ITR#7036 Remove all reference to pool and replace by volume
- Fixed ITR#7040 WebUI - Setting Timezones reports error even though it worked correctly.
- Fixed ITR#7056 Create volume does not work
- Fixed ITR#7060 Creating mirror using auto configuration failed for requested size does not fit
- Fixed ITR#7062 Resizing of a volume on USB Drive does not work
- Fixed ITR#7065 Cancel Button should grey out after disk resize
- Fixed ITR#7066 Used Defaults to created a Mirrored volume and got an operation failed message.
- Fixed ITR#7071 Resizing the volume to use maximum available space on system drive failed
- Fixed ITR#7073 Create a Volume - Operation Failed
- Added drive_info.asp, pool_info.asp and share_info.asp for EasyLink
Build R.0.9.1_85-93 4/18/05
- Fixed ITR#7043 Remove all refrence to Striping from Disk Management Menu
- Fixed ITR#7048 No safe removal for USB blank or unclaimed Hard Disk
- Fixed ITR#7049 No warning when attempting to remove a volume containing the printer pool
- Fixed ITR#7050 Irregular table for mirror volume status
- Fixed ITR#7051 FW Upgrade accepts invalid file name or blank as an iput
- Fixed ITR#7061 Resize volume display Disk Assignement Displayed not aligned properly
- Fixed ITR#7059 FW Upgrade Compete -- Wrong spelling
- Fixed ITR#7065 Cancel Button should grey out after disk resize
- Always set "kernel_boot_wait_gpio" to 0 in startup script
- Changed firmware image file extention to .wdf
Build R.0.9.1_83-92 4/13/05
- Fixed ITR#7056 Create volume does not work
- Fixed ITR#7055 250GB Drive capacity shown as 238.5GB only
Build R.0.9.1_80-91 4/12/05
- Fixed ITR#6973 Resizing volume does not reject value > available space
- Fixed ITR#6974 Resize volume - allows entry of size < used space on the volume
- Fixed ITR#6983 Documentation note. Problem if browser has JavaScript disabled
- Fixed ITR#6984 Print spooler is exposed to end user and can be deleted.
- Fixed ITR#6994 Drive capacity reported is greater then the usable capacity of the drive.
- Fixed ITR#7001 Cannot create share on a volume when volume name has space in name.
- Fixed ITR#7033 Resize volume can take up to 3 minutes if the Navigator in on WD network
- Fixed ITR#7036 Remove all reference to pool and replace by volume
- Fixed ITR#7038 Limit the number of volumes creation to ten volumes only (Documentation)
- Fixed ITR#7041 Rename volume allows space in the name
- Fixed ITR#7043 Remove all reference to Striping from Disk Management Menu
- Fixed ITR#7048 No safe removal for USB blank or unclaimed Hard Disk
- Fixed ITR#7049 No warming when attempting to remove a volume containing the printer pool
- Fixed ITR#7050 Irregular table for mirror volume status
- Added check for blank disk and flash LED
- Update info dump page
Build R.0.9.1_72-90 4/5/05
- Fixed Logger usage
- Fixed syslogd
- Removed step4 in Initial Setup wizard
- Added Printer Sharing update (just ability to enable and disable)
Build R.0.9.1_59-89 3/31/05
- Migrated to Broadcom 1.2 beta 1
Build R.0.9.1_57-88 3/30/05
- Fixed claim and unclaim issue
- Updated CFE MAC address
- Enabled new_disk_action
Build R.0.9.1_53-87 3/29/05
- Added kernel_boot_wait_gpio in webhook
- Added drive management UI update
Build 86
- Added USB safe remove button and other UI changes
- Added kernel_boot_wait_gpio checking
- Added force_ide_cable_select
Build 85
- Fixed WDNVRAMSETUP script
Build 84
- Added latsst UI cahnge
- Added support for 8mb flash image
Build 82
- WEb UI
* Restarted CIF service after machine name change
Build R.0.9.1_42-81 3/16/05
- Linux driver
* Fixed NVRAM I/O error with cfi_cmdset_0002.c
Build 80
- Web UI
* Fixed Logon message
Build 79
- Web UI
* Fixed eula.asp missing issue
Build 78
- Added Marc latest UI change
- Fixed share creatation issue
Build 73
- Web UI
* Added Marc's latest changes
> Add a share is now a wizard
> Various improvements to the setup wizard
- WDNS
* Bug fixed relating to the nfs service not being created correctly
* Removed bitfields in the library since they are not endian
compatible
* Service info replies are now always 512 bytes big for forwards
compatibility
- Misc
* Broadcom's string tables were all updated to replace references of
Broadnas or Broadcom with WD NetCenter
Build 63
- WDNS now uses nvram variables to get the machine name and to check if
the web UI has been used to configure the device yet
Build 60
- Syabase UPnP removed from the build, but not removed from the project
- 'tmp' location now set as a environment variable instead of an nvram variable
Build 58
- Syabase UPnP integrated into firmware images
- Firmware now is based off of split design
- All nvram changes that were in the scripts are now in the cfe
Build 48
- The wdscripts now do less because we have our own CFE
Build 47
- Started firmware and release notes naming convention
- Began populating values for default_* nvram variables
- Firmware update page now lists build number and tree version
- Version.asp page no longer exists
Build 44
- Fixed spelling mistake in file transfer priorities wizard intro page
Build 43
- Started these release notes
- Enabled the first draft of the file transfer priorities wizard